-
Dynam Waco Red 1270mm 50inch Wingspan RC Airplane PNP
$309.00
$226.99 -
Dynam Cessna 310 Grand Cruiser V2 Electric RC Airplane PNP 1280mm Wingspan With Flaps Red
$359.00
$225.99 -
Starmax F-22 Raptor 70mm EDF Jet Electric R/C RC Airplane Plane Ready-To-Fly
$389.92
$219.97 -
Volantex RC Vector 80 (cm) High speed ABS Unibody Boats 798-1 brushless PNP
$229.00
$121.99 -
2.4Ghz 4-CH 64mm EDF F-15 Remote Control Jet w/ Brushless Motor/ESC/Lipo 100% RTF Grey
$369.00
$239.97 -
P-51 P51 P-51D Mustang 2.4G 4CH Electric R/C RC Airplane Plane 100% Ready To Fly
$259.92 -
Dynam Devil 3D Sport Aerobatic Bi-Plane EPO Electric RC Plane PNP
$319.00
$258.97 -
EX-Hobby Ranger600 Glider with Xpilot Stabilization System and One Key U-turn Function (761-2) Ready-To-Fly Out Of Box
$129.00
$99.97 -
VolantexRC Vector28 2.4Ghz Super High Speed Pool Racer RC Boat (795-1) Ready-To-Run
$135.00
$39.97 -
PBY Catalina 2.4G Brushless/LIPO Electric RC Airplane PNP
$359.00
$238.97
Product Description
Bonanza is based on the late 1940’s civilian aircraft the Beechcraft Bonanza.
With a low wing and a wingspan of only 950mm, this is a plane that you can take
anywhere. Durafly has designed it as an easy hand launcher.
It is built of superbly finished, tough EPO and comes with stickers already applied. All electrics are pre-installed, just fit your receiver and battery. For better control, Durafly has fitted ball links on all control surfaces. The Bonanza is ready to "Throw it and Show it"
The Bonanza has a big wing that makes it a stable flier, but has heaps of power and will easily do the major tricks, loops and rolls, with poise. After a successful flight, you can slow down and float in for a stress-free belly landing.
Features:
• Quick, easy assembly
• Superbly finished, highly compressed EPO construction
• Hand launch, belly landing
• 4 Channels (ailerons, elevator, rudder (V-Tail), throttle)
• Ball links for control surfaces
• Strong, fully molded plastic cowl and belly skid
• Full 4 channel control: Elevator, rudder, throttle and aileron
• V-Tail tailplane
• Aileron servo covers
Specs:
Wingspan: 950mm (37.4")
Length: 650mm (25.6")
Flying Weight: 540g (19.5oz) (inc all electronics and battery)
Servo: 9g x 4
ESC: 20A
Motor: 1300KV
Propeller: 7x5
Suggested battery: 3S 1300mAh
CG position: 70mm +/- 5mm
Control surface throws: ±8mm
Suggested Set-Up:
C of G: 90mm ± 5mm (measured from leading edge at root of wing)
Elevator: 8mm each way (+ 30% exponential)
Ailerons: 8mm each way (+ 25% exponential)
Rudder: 12mm each way (+ 25% exponential)
Required (not included):
Minimum 4ch Transmitter capable of V-Tail mixing
Appropriate 4ch receiver
1 x 1300mAh 3S LiPo battery
CA Glue
It is built of superbly finished, tough EPO and comes with stickers already applied. All electrics are pre-installed, just fit your receiver and battery. For better control, Durafly has fitted ball links on all control surfaces. The Bonanza is ready to "Throw it and Show it"
The Bonanza has a big wing that makes it a stable flier, but has heaps of power and will easily do the major tricks, loops and rolls, with poise. After a successful flight, you can slow down and float in for a stress-free belly landing.
Features:
• Quick, easy assembly
• Superbly finished, highly compressed EPO construction
• Hand launch, belly landing
• 4 Channels (ailerons, elevator, rudder (V-Tail), throttle)
• Ball links for control surfaces
• Strong, fully molded plastic cowl and belly skid
• Full 4 channel control: Elevator, rudder, throttle and aileron
• V-Tail tailplane
• Aileron servo covers
Specs:
Wingspan: 950mm (37.4")
Length: 650mm (25.6")
Flying Weight: 540g (19.5oz) (inc all electronics and battery)
Servo: 9g x 4
ESC: 20A
Motor: 1300KV
Propeller: 7x5
Suggested battery: 3S 1300mAh
CG position: 70mm +/- 5mm
Control surface throws: ±8mm
Suggested Set-Up:
C of G: 90mm ± 5mm (measured from leading edge at root of wing)
Elevator: 8mm each way (+ 30% exponential)
Ailerons: 8mm each way (+ 25% exponential)
Rudder: 12mm each way (+ 25% exponential)
Required (not included):
Minimum 4ch Transmitter capable of V-Tail mixing
Appropriate 4ch receiver
1 x 1300mAh 3S LiPo battery
CA Glue