-
Dynam F6F Hellcat V2 50'' 1270mm Electric RC Airplane PNP With Flaps and Retracts
$359.00
$235.97 -
Dynam Cessna 188 Crop Duster 59''/1500mm Electric RC Plane Blue Ready-To-Fly
$429.00
$319.97 -
Everest-10 1/10 Scale Crawler 2.4GHz Blue
$299.00
$180.97 -
TopRC A1 White 800mm/32'' EPO Electric RC Airplane PNP
$199.00
$98.99 -
Dynam Cessna 188 Crop Duster 59''/1500mm PNP Electric RC Plane Orange
$319.00
$178.99 -
VolantexRC Vector 40(cm) High speed racing boat ABS Unibody (797-1) Ready-To-Run Brushed Version
$139.00
$55.97 -
DW Hobby 61" Fokker DR1 Triplane Laser Cut Balsawood RC Airplane Model Kit
$506.00
$259.97 -
PBY Catalina 2.4G Brushless/LIPO Electric RC Airplane Ready-To-Fly
$399.00
$319.97 -
Dynam T-28 Trojan V2 1270mm EPO RC Plane With Retracts PNP Yellow
$319.00
$229.97 -
VolanterRC FPVraptor V2 Tower UAV Trim Scheme 2M Unibody Pusher (757-V2) Eelctric RC Glider Kit Version
$159.00
$109.97
Product Description
Bonanza is based on the late 1940’s civilian aircraft the Beechcraft Bonanza.
With a low wing and a wingspan of only 950mm, this is a plane that you can take
anywhere. Durafly has designed it as an easy hand launcher.
It is built of superbly finished, tough EPO and comes with stickers already applied. All electrics are pre-installed, just fit your receiver and battery. For better control, Durafly has fitted ball links on all control surfaces. The Bonanza is ready to "Throw it and Show it"
The Bonanza has a big wing that makes it a stable flier, but has heaps of power and will easily do the major tricks, loops and rolls, with poise. After a successful flight, you can slow down and float in for a stress-free belly landing.
Features:
• Quick, easy assembly
• Superbly finished, highly compressed EPO construction
• Hand launch, belly landing
• 4 Channels (ailerons, elevator, rudder (V-Tail), throttle)
• Ball links for control surfaces
• Strong, fully molded plastic cowl and belly skid
• Full 4 channel control: Elevator, rudder, throttle and aileron
• V-Tail tailplane
• Aileron servo covers
Specs:
Wingspan: 950mm (37.4")
Length: 650mm (25.6")
Flying Weight: 540g (19.5oz) (inc all electronics and battery)
Servo: 9g x 4
ESC: 20A
Motor: 1300KV
Propeller: 7x5
Suggested battery: 3S 1300mAh
CG position: 70mm +/- 5mm
Control surface throws: ±8mm
Suggested Set-Up:
C of G: 90mm ± 5mm (measured from leading edge at root of wing)
Elevator: 8mm each way (+ 30% exponential)
Ailerons: 8mm each way (+ 25% exponential)
Rudder: 12mm each way (+ 25% exponential)
Required (not included):
Minimum 4ch Transmitter capable of V-Tail mixing
Appropriate 4ch receiver
1 x 1300mAh 3S LiPo battery
CA Glue
It is built of superbly finished, tough EPO and comes with stickers already applied. All electrics are pre-installed, just fit your receiver and battery. For better control, Durafly has fitted ball links on all control surfaces. The Bonanza is ready to "Throw it and Show it"
The Bonanza has a big wing that makes it a stable flier, but has heaps of power and will easily do the major tricks, loops and rolls, with poise. After a successful flight, you can slow down and float in for a stress-free belly landing.
Features:
• Quick, easy assembly
• Superbly finished, highly compressed EPO construction
• Hand launch, belly landing
• 4 Channels (ailerons, elevator, rudder (V-Tail), throttle)
• Ball links for control surfaces
• Strong, fully molded plastic cowl and belly skid
• Full 4 channel control: Elevator, rudder, throttle and aileron
• V-Tail tailplane
• Aileron servo covers
Specs:
Wingspan: 950mm (37.4")
Length: 650mm (25.6")
Flying Weight: 540g (19.5oz) (inc all electronics and battery)
Servo: 9g x 4
ESC: 20A
Motor: 1300KV
Propeller: 7x5
Suggested battery: 3S 1300mAh
CG position: 70mm +/- 5mm
Control surface throws: ±8mm
Suggested Set-Up:
C of G: 90mm ± 5mm (measured from leading edge at root of wing)
Elevator: 8mm each way (+ 30% exponential)
Ailerons: 8mm each way (+ 25% exponential)
Rudder: 12mm each way (+ 25% exponential)
Required (not included):
Minimum 4ch Transmitter capable of V-Tail mixing
Appropriate 4ch receiver
1 x 1300mAh 3S LiPo battery
CA Glue